Actuator

An actuator is a component of a machine that produces force, torque, or displacement, when an electrical, pneumatic or hydraulic input is supplied to it in a system (called an actuating system). The effect is usually produced in a controlled way.[1] An actuator translates such an input signal into the required form of mechanical energy. It is a type of transducer.[2] In simple terms, it is a "mover".

An actuator requires a control device (which provides control signal) and a source of energy. The control signal is relatively low in energy and may be voltage, electric current, pneumatic, or hydraulic fluid pressure, or even human power[clarification needed].[3] In the electric, hydraulic, and pneumatic sense, it is a form of automation or automatic control.

The displacement achieved is commonly linear or rotational, as exemplified by linear motors and rotary motors, respectively. Rotary motion is more natural for small machines making large displacements. By means of a leadscrew, rotary motion can be adapted to function as a linear actuator (which produces a linear motion, but is not a linear motor).

Another broad classification of actuators separates them into two types: incremental-drive actuators and continuous-drive actuators. Stepper motors are one type of incremental-drive actuators. Examples of continuous-drive actuators include DC torque motors, induction motors, hydraulic and pneumatic motors, and piston-cylinder drives (rams).[4]

Types of actuators

Mechanical

An actuator can be just a mechanism that is directly driven by the motions or forces of other parts of the system. An example is the camshafts that drive the intake and exhaust valves in internal combustion engines, driven by the engine itself. Another example is the mechanism that strikes the hours in a traditional grandfather clock or cuckoo clock.

Hydraulic

A hydraulic actuator typically uses the pressure of a liquid (usually oil) to cause a piston to slide inside a hollow cylindrical tube linear, rotatory or oscillatory motion. In a single acting actuator the fluid pressure is applied to just one side of the piston, so that it applies useful force in only one direction. The opposite motion may be effected by a spring, by gravity, or by other forces present in the system. In a double acting actuator, the return stroke is driven by fluid pressure applied to the opposite side of the piston.[5]

Since liquids are nearly impossible to compress, a hydraulic actuator can exert a large force. The drawback of this approach is its limited acceleration. They respond quickly to input changes, have little inertia, can operate continuously over a relatively large working range, and can hold their position without any significant energy input.

A hydraulic actuator can be used to displace the rack of a rack and pinion mechanism, causing the pinion to turn. This arrangement is used, for example, to operate valves in pipelines and other industrial fluid transport installations.[6]

Pneumatic

Pneumatic actuator operating a valve through a rack-and-pinion mechanism.[7]

A pneumatic actuator is similar to a hydraulic one but uses a gas (usually air) instead of a liquid.[8][9] Compared to hydraulic actuators, pneumatic ones are less complicated because they do not need pipes for the return and recycling of the working fluid. On the other hand, they still need external infrastructure such as compressors, reservoirs, filters, and air treatment subsystems, which often makes them less convenient that electrical and electromechanical actuators.

In the first steam engines and in all steam locomotives, steam pressure is used to drive pneumatic actuators to produce a reciprocating motion, which is converted to rotary motion by some sort of crankshaft mechanism.

Electric

Electric valve actuator controlling a ½ needle valve.

Since 1960, several actuator technologies have been developed. Electric actuators can be classified in the following groups:

Electromechanical

An electromechanical actuator (EMA) uses mechanical means to convert the rotational force of an ordinary (rotary) electric motor into a linear movement. The mechanism may be a toothed belt or a screw (either a ball or a lead screw or planetary roller screw).

The main advantages of electromechanical actuators are their relatively good level of accuracy with respect to pneumatics, their possible long lifecycle and the little maintenance effort required (might require grease). It is possible to reach relatively high force, on the order of 100 kN.

The main limitation of these actuators are the reachable speed, the important dimensions and weight they require. The main application of such actuators is mainly seen in health care devices and factory automation.

Electrohydraulic

Another approach is an electrohydraulic actuator, where the electric motor remains the prime mover but provides torque to operate a hydraulic accumulator that is then used to transmit actuation force in much the same way that diesel engine/hydraulics are typically used in heavy equipment.

Electrical energy is used to actuate equipment such as multi-turn valves, or electric-powered construction and excavation equipment.

When used to control the flow of fluid through a valve, a brake is typically installed above the motor to prevent the fluid pressure from forcing open the valve. If no brake is installed, the actuator gets activated to reclose the valve, which is slowly forced open again. This sets up an oscillation (open, close, open ...) and the motor and actuator will eventually become damaged.[10]

Rotary

Electric rotary actuators use a rotary motor to turn the target part over a certain angle.[11] Rotary actuators can have up to a rotation of 360 degrees. This allows it to differ from a linear motor as the linear is bound to a set distance compared to the rotary motor. Rotary motors have the ability to be set at any given degree in a field making the device easier to set up still with durability and a set torque.

Rotary motors can be powered by 3 different techniques such as Electric, Fluid, or Manual.[12] However, Fluid powered rotary actuators have 5 sub-sections of actuators such as Scotch Yoke, Vane, Rack-and-Pinion, Helical, and Electrohydraulic. All forms have their own specific design and use allowing the ability to choose multiple angles of degree.

Applications for the rotary actuators are just about endless but, will more than likely be found dealing with mostly hydraulic pressured devices and industries. Rotary actuators are even used in the robotics field when seeing robotic arms in industry lines. Anything you see that deals with motion control systems to perform a task in technology is a good chance to be a rotary actuator.[12]

Linear

A linear electric actuator uses a linear motor, which can be thought as a rotary electric motor which has been cut and unrolled. Thus, instead of producing a rotational movement, it produces a linear force along their length. Because it generally has lower friction losses than the alternatives, a linear electric actuator can last over a hundred million cycles.

Linear motors are divided in 3 basic categories: flat linear motor (classic), U-Channel linear motors and Tubular linear motors.

Linear motor technology is the best solution in the context of a low load (up to 30Kgs) because it provides the highest level of speed, control and accuracy.

In fact, it represents the most desired and versatile technology. Due to the limitations of pneumatics, the current electric actuator technology is a viable solution for specific industry applications and it has been successfully introduced in market segments such as the watchmaking, semiconductor and pharmaceutical industries (as high as 60% of the applications. The growing interest for this technology, can be explained by the following characteristics:

  • High precision (equal or less than 0,1 mm);
  • High cycling rate (greater than 100 cycles/min);
  • Possible usage in clean and highly-regulated environments (no leakages of air, humidity or lubricants allowed);
  •  Need for programmable motion in the situation of complex operations

The main disadvantages of linear motors are:

  • They are expensive respect to pneumatics and other electric technologies.
  • They are not easy to integrate in standard machineries due to their important size and high weight.
  • They have a low force density respect to pneumatic and electromechanical actuators.

Thermal

An actuator may be driven by heat through the expansion that most solid material exhibit when the temperature increases. This principle is commonly used, for example, to operate electric switches in thermostats. Typically, a (non-electronic) thermostat contains a strip with two layers of different metals, that will bend when heated.

Thermal actuators may also exploit the properties of shape-memory alloys.[13]

Magnetic

Some actuators are driven by externally applied magnetic fields. They typically contain parts made of ferromagnetic materials that are strongly attracted to each other when they are magnetized by the external field. An example are the reed switches that may be used as door opening sensors in a building security system.

Alternatively, magnetic actuators can use magnetic shape-memory alloys.

Thermal actuators

Soft actuators

A soft actuator is made of a flexible material that changes its shape in response to stimuli including mechanical, thermal, magnetic, and electrical. Soft actuators mainly deal with the robotics of humans rather than industry which is what most of the actuators are used for. For most actuators they are mechanically durable yet do not have an ability to adapt compared to soft actuators. The soft actuators apply to mainly safety and healthcare for humans which is why they are able to adapt to environments by disassembling their parts.[14] This is why the driven energy behind soft actuators deal with flexible materials like certain polymers and liquids that are harmless

The majority of the existing soft actuators are fabricated using multistep low yield processes such as micro-moulding,[15] solid freeform fabrication,[16] and mask lithography.[17] However, these methods require manual fabrication of devices, post processing/assembly, and lengthy iterations until maturity in the fabrication is achieved. To avoid the tedious and time-consuming aspects of the current fabrication processes, researchers are exploring an appropriate manufacturing approach for effective fabrication of soft actuators. Therefore, special soft systems that can be fabricated in a single step by rapid prototyping methods, such as 3D printing, are utilized to narrow the gap between the design and implementation of soft actuators, making the process faster, less expensive, and simpler. They also enable incorporation of all actuator components into a single structure eliminating the need to use external joints, adhesives, and fasteners.

Shape memory polymer (SMP) actuators are the most similar to our muscles, providing a response to a range of stimuli such as light, electrical, magnetic, heat, pH, and moisture changes. They have some deficiencies including fatigue and high response time that have been improved through the introduction of smart materials and combination of different materials by means of advanced fabrication technology. The advent of 3D printers has made a new pathway for fabricating low-cost and fast response SMP actuators. The process of receiving external stimuli like heat, moisture, electrical input, light or magnetic field by SMP is referred to as shape memory effect (SME). SMP exhibits some rewarding features such a low density, high strain recovery, biocompatibility, and biodegradability.

Photopolymers or light activated polymers (LAP) are another type of SMP that are activated by light stimuli. The LAP actuators can be controlled remotely with instant response and, without any physical contact, only with the variation of light frequency or intensity.

A need for soft, lightweight and biocompatible soft actuators in soft robotics has influenced researchers for devising pneumatic soft actuators because of their intrinsic compliance nature and ability to produce muscle tension.

Polymers such as dielectric elastomers (DE), ionic polymer–metal composites (IPMC), ionic electroactive polymers, polyelectrolyte gels, and gel-metal composites are common materials to form 3D layered structures that can be tailored to work as soft actuators. EAP actuators are categorized as 3D printed soft actuators that respond to electrical excitation as deformation in their shape.

Examples and applications

In engineering, actuators are frequently used as mechanisms to introduce motion, or to clamp an object so as to prevent motion.[18] In electronic engineering, actuators are a subdivision of transducers. They are devices which transform an input signal (mainly an electrical signal) into some form of motion.

Examples of actuators

Circular to linear conversion

Motors are mostly used when circular motions are needed, but can also be used for linear applications by transforming circular to linear motion with a lead screw or similar mechanism. On the other hand, some actuators are intrinsically linear, such as piezoelectric actuators. Conversion between circular and linear motion is commonly made via a few simple types of mechanism including:

Virtual instrumentation

In virtual instrumentation, actuators and sensors are the hardware complements of virtual instruments.

Performance metrics

Performance metrics for actuators include speed, acceleration, and force (alternatively, angular speed, angular acceleration, and torque), as well as energy efficiency and considerations such as mass, volume, operating conditions, and durability, among others.

Force

When considering force in actuators for applications, two main metrics should be considered. These two are static and dynamic loads. Static load is the force capability of the actuator while not in motion. Conversely, the dynamic load of the actuator is the force capability while in motion.

Speed

Speed should be considered primarily at a no-load pace, since the speed will invariably decrease as the load amount increases. The rate the speed will decrease will directly correlate with the amount of force and the initial speed.

Operating conditions

Actuators are commonly rated using the standard IP Code rating system. Those that are rated for dangerous environments will have a higher IP rating than those for personal or common industrial use.

Durability

This will be determined by each individual manufacturer, depending on usage and quality.

See also

References

  1. ^ Escudier, Marcel; Atkins, Tony (2019). "A Dictionary of Mechanical Engineering". Oxford Reference. doi:10.1093/acref/9780198832102.001.0001. ISBN 978-0-19-883210-2.
  2. ^ Butterfield, Andrew J.; Szymanski, John, eds. (2018). "A Dictionary of Electronics and Electrical Engineering". Oxford Reference. doi:10.1093/acref/9780198725725.001.0001. ISBN 978-0-19-872572-5.
  3. ^ Nesbitt, B. (2011). Handbook of Valves and Actuators: Valves Manual International. Elsevier Science. p. 2. ISBN 978-0-08-054928-6. Retrieved 2021-11-11.
  4. ^ Clarence W. de Silva. Mechatronics: An Integrated Approach (2005). CRC Press. p. 761.
  5. ^ "What's the Difference Between Pneumatic, Hydraulic, and Electrical Actuators?". machinedesign.com. Archived from the original on 2016-04-23. Retrieved 2016-04-26.
  6. ^ "The Role of Rack and Pinion Actuators in On-Off & Modulating Controls". Valve Magazine (Spring 2010). Valve Manufacturers Association.
  7. ^ "Automax SuperNova Series Pneumatic Rack & Pinion Actuators" (PDF). Flowserve Corporation. Retrieved 7 July 2014.
  8. ^ "What is a Pneumatic Actuator?". www.tech-faq.com. Archived from the original on 2018-02-21. Retrieved 2018-02-20.
  9. ^ "Pneumatic Valve Actuators Information - IHS Engineering360". www.globalspec.com. Archived from the original on 2016-06-24. Retrieved 2016-04-26.
  10. ^ Tisserand, Olivier. "How does an electric actuator work?". Archived from the original on 2018-02-21. Retrieved 2018-02-20.
  11. ^ "What Are the Differences Between Linear and Rotary Actuators?". RoboticsTomorrow. Retrieved 2022-07-13.
  12. ^ a b "Rotary Actuator - an overview". ScienceDirect Topics. Retrieved 2022-07-13.
  13. ^ "Ultra-compact: Valves with shape memory actuators". 24 March 2021.
  14. ^ El-Atab, Nazek; Mishra, Rishabh B.; Al-Modaf, Fhad; Joharji, Lana; Alsharif, Aljohara A.; Alamoudi, Haneen; Diaz, Marlon; Qaiser, Nadeem; Hussain, Muhammad Mustafa (October 2020). "Soft Actuators for Soft Robotic Applications: A Review". Advanced Intelligent Systems. 2 (10): 2000128. doi:10.1002/aisy.202000128. hdl:10754/664810. ISSN 2640-4567. S2CID 224805628.
  15. ^ Feng, Guo-Hua; Yen, Shih-Chieh (2015). "Micromanipulation tool replaceable soft actuator with gripping force enhancing and output motion converting mechanisms". 2015 Transducers - 2015 18th International Conference on Solid-State Sensors, Actuators and Microsystems (TRANSDUCERS). pp. 1877–80. doi:10.1109/TRANSDUCERS.2015.7181316. ISBN 978-1-4799-8955-3. S2CID 7243537.
  16. ^ Malone, Evan; Lipson, Hod (2006). "Freeform fabrication of ionomeric polymer-metal composite actuators". Rapid Prototyping Journal. 12 (5): 244–53. doi:10.1108/13552540610707004. S2CID 1172362.
  17. ^ Kerdlapee, Pongsak; Wisitsoraat, Anurat; Phokaratkul, Ditsayuth; Leksakul, Komgrit; Phatthanakun, Rungreung; Tuantranont, Adisorn (2013). "Fabrication of electrostatic MEMS microactuator based on X-ray lithography with Pb-based X-ray mask and dry-film-transfer-to-PCB process". Microsystem Technologies. 20: 127–35. doi:10.1007/s00542-013-1816-x. S2CID 110234049.
  18. ^ Shabestari, N. P. (2019). "Fabrication of a simple and easy-to-make piezoelectric actuator and its use as phase shifter in digital speckle pattern interferometry". Journal of Optics. 48 (2): 272–282. Bibcode:2019JOpt...48..272P. doi:10.1007/s12596-019-00522-4. S2CID 155531221.
  19. ^ Sclater, N. (2007). Mechanisms and Mechanical Devices Sourcebook (4th ed.). McGraw-Hill.

Read other articles:

ВільвокансVillevocance Країна  Франція Регіон Овернь-Рона-Альпи  Департамент Ардеш  Округ Турнон-сюр-Рон Кантон Анноне-Сюд Код INSEE 07342 Поштові індекси 07690 Координати 45°13′32″ пн. ш. 4°35′20″ сх. д.H G O Висота 380 - 912 м.н.р.м. Площа 9,38 км² Населення 1183 (01-2020[1]) Густот...

 

Defunct American telecommunications company Sprint CorporationFormer Sprint World Headquarters Campus in Overland Park, Kansas, U.S.FormerlyBrown Telephone Company (1899–1911)United Telephone Company (1911–1925)United Telephone and Electric (1925–1938)United Utilities, Inc. (1938–1972)United Telecommunications and United Telephone System (1972–1987)Sprint Corporation (1987–2005, 2013–2020)Sprint Nextel Corporation (2005–2013)TypePublicTraded asNYSE: SIndustryTelecommunica...

 

?†Resoviaornis jamroziЧас існування: олігоцен, 29 млн років тому Біологічна класифікація Домен: Ядерні (Eukaryota) Царство: Тварини (Animalia) Тип: Хордові (Chordata) Клас: Птахи (Aves) Ряд: Горобцеподібні (Passeriformes) Рід: †ResoviaornisZ. M. Bocheński et al., 2013 Вид: †R. jamrozi Біноміальна назва Resoviaornis jamroziZ. M. Bocheński et...

Public school in Hampstead, London, This article needs additional citations for verification. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed.Find sources: University College School – news · newspapers · books · scholar · JSTOR (September 2019) (Learn how and when to remove this template message) University College SchoolLocationFrognal, London, NW3EnglandCoordinates51°33′12...

 

Esta página cita fontes, mas que não cobrem todo o conteúdo. Ajude a inserir referências. Conteúdo não verificável pode ser removido.—Encontre fontes: ABW  • CAPES  • Google (N • L • A) (Novembro de 2014) Não compre produtos russos!Не купуй російське! Flash mob em frente a uma loja de roupas russa da rede OGGI, em Kiev, com cartazes Não compre produtos russos!. Datas das operações 14 agosto 2013 (2...

 

American comedy drama television series TransparentGenreComedy dramaCreated byJoey SolowayStarring Jeffrey Tambor Gaby Hoffmann Jay Duplass Amy Landecker Judith Light Kathryn Hahn Country of originUnited StatesOriginal languageEnglishNo. of seasons5No. of episodes41 (list of episodes)ProductionExecutive producers Joey Soloway Andrea Sperling ProducerVictor HsuProduction locationLos AngelesEditors Catherine Haight Annette Davey David Bertman Hilda Rasula Camera setupJim FrohnaRunning time27–...

سوفولك     الإحداثيات 36°44′28″N 76°36′35″W / 36.7411°N 76.6097°W / 36.7411; -76.6097  [1] تاريخ التأسيس 1742  سبب التسمية سوفولك  تقسيم إداري  البلد الولايات المتحدة[2][3]  التقسيم الأعلى فرجينيا  خصائص جغرافية  المساحة 1110.863244 كيلومتر مربع1111.338608 كيلوم...

 

Andy OppenheimerAIExpE MIABTIBorn1953 (age 69–70)NationalityBritish-IrishAlma materLiverpool University Andy Oppenheimer AIExpE MIABTI (born 1953) is a UK-based expert and consultant in counter-terrorism and CBRNE (chemical, biological, radiological, nuclear weapons and explosives). Since 2001 he has written articles, edited journals, and presented at conferences and professional seminars worldwide. He has been editor of several journals on defence and security, including Chem...

 

توماس فرانسيس الأصغر Thomas Francis Jr معلومات شخصية الميلاد 15 يوليو 1900(1900-07-15)غاز سيتي، إنديانا، الولايات المتحدة الوفاة 1 أكتوبر 1969 (69 سنة)آن آربر، ميشيغان، الولايات المتحدة الجنسية أمريكي عضو في الأكاديمية الوطنية للعلوم،  والأكاديمية الأمريكية للفنون والعلوم  الحياة الع...

هذه المقالة يتيمة إذ تصل إليها مقالات أخرى قليلة جدًا. فضلًا، ساعد بإضافة وصلة إليها في مقالات متعلقة بها. (مارس 2019) انتخابات الرئاسة التشيلية 1927 1927 البلد تشيلي التاريخ 22 مايو 1927  انتخابات الرئاسة التشيلية 1925  انتخابات الرئاسة التشيلية 1931  مرشحون كارلوس إيبانيز ديل ...

 

العلاقات الأنغولية الرواندية أنغولا رواندا   أنغولا   رواندا تعديل مصدري - تعديل   العلاقات الأنغولية الرواندية هي العلاقات الثنائية التي تجمع بين أنغولا ورواندا.[1][2][3][4][5] مقارنة بين البلدين هذه مقارنة عامة ومرجعية للدولتين: وجه المقارنة ...

 

For traffic collisions that occurred after the year 2000 and all the way up to the present, see List of traffic collisions (2000–present), for notable people who died in traffic collisions, see List of people who died in traffic collisions. This article contains dynamic lists that may never be able to satisfy particular standards for completeness. You can help by adding missing items with reliable sources. This article needs additional citations for verification. Please help improve this ar...

Independent city in Virginia, United States This article is about the independent city surrounded by Fairfax County. For the county, see Fairfax County, Virginia. For the town in Culpeper County, formerly named Fairfax, see Culpeper, Virginia. Independent city in Virginia, United StatesFairfax, VirginiaIndependent cityFairfax's Old Town section in 2007 FlagSealLogoNicknames: Downtown Fairfax, Fairfax City, Historic FairfaxLocation of Fairfax in VirginiaFairfax CityShow map of Northern Vi...

 

Эта статья или раздел нуждается в переработке.Пожалуйста, улучшите статью в соответствии с правилами написания статей. (28 мая 2023)У этого термина существуют и другие значения, см. Max.Max URL max.com (англ.) Коммерческий да Тип сайта Стриминговый видеосервис Регистрация Необход...

 

Luwu pada Pekan Olahraga Provinsi Sulawesi Selatan 2022 Ketua kontingen Andi Muhammad Arfan Basmin Warna kebanggaan  BIRU TUA  Moto kontingen Kami Luwu, Kami Sulsel, Kami Bersaudara Peringkat sebelumnya 19 dari 24 kontingen Jumlah atlet 140 orang Jumlah cabang olahraga resmi yang diikuti 18 cabang olahraga Jumlah cabang olahraga eksibisi yang diikuti TBA cabang olahraga Jumlah pendukung atlet (ofisial, pelatih, asisten pelatih, manajer, panitia kontingen, instansi pendukung) 251 ora...

Great-Smoky-Mountains-Nationalpark Panorama der Berglandschaft im Great-Smoky-Mountains-NationalparkPanorama der Berglandschaft im Great-Smoky-Mountains-Nationalpark Great-Smoky-Mountains-Nationalpark (USA) 35.687034333333-83.536831166667Koordinaten: 35° 41′ 13″ N, 83° 32′ 13″ W Lage: Tennessee, Vereinigte Staaten Nächste Stadt: Knoxville (Tennessee) Fläche: 2.114,2 km² Gründung: 15. Juni 1934 Besucher: 11.421.200 (2018) Adresse: Great Smo...

 

American academic and social worker Helen Dingmanphotograph from the collections of Berea CollegeBornHelen Hastie Dingman(1885-02-05)February 5, 1885Spring Valley, Rockland County, New YorkDiedApril 22, 1978(1978-04-22) (aged 93)Berea, KentuckyNationalityAmericanOther namesHelen H. DingmanOccupation(s)academic, social workerYears active1914-1952 Helen Dingman (February 5, 1885 – April 22, 1978) was an American academic and social worker who was one of the central figures in t...

 

Keith Bogans Bogans con la maglia dei Chicago Bulls Nazionalità  Stati Uniti Altezza 196 cm Peso 98 kg Pallacanestro Ruolo Allenatore (ex guardia) Termine carriera 2016 - giocatore Carriera Giovanili DeMatha Catholic High School1999-2003 Kentucky Wildcats135 (1.923) Squadre di club 2003-2004 Orlando Magic73 (498)2004-2006 Charlotte Bobcats113 (1.055)2006 Houston Rockets33 (281)2006-2009 Orlando Magic177 (1.198)2009 Milwaukee Bucks29 (175)2009-2010 San ...

パロアルト研究所Palo Alto Research Center Inc.略称 PARC本社所在地 アメリカ合衆国カリフォルニア州パロアルト3333 Coyote Hill Rd設立 1970年事業内容 研究開発主要株主 SRIインターナショナル外部リンク https:/parc.com/テンプレートを表示 正面玄関 パロアルト研究所(パロアルトけんきゅうじょ、Palo Alto Research Center、PARC)は、アメリカ合衆国のカリフォルニア州パロアルトにある研...

 

Pour un article plus général, voir PlayStation. Sony Net Yaroze avec son kit de developpement. La Net Yaroze (ネットやろうぜ, Netto Yarōze?) est un kit de développement pour PlayStation, sorti en 1996 au Japon et en 1997 dans les autres territoires, destiné aux développeurs amateurs. Elle a été conçue par Ken Kutaragi. Ce kit comprend une console PlayStation non zonée, de couleur noire et d'une texture différente de la machine courante, avec un BIOS différent qui lui perme...

 

Strategi Solo vs Squad di Free Fire: Cara Menang Mudah!