For the children's toy gun which fires small pieces of potato, see Spud gun.
This article's lead sectionmay be too short to adequately summarize the key points. Please consider expanding the lead to provide an accessible overview of all important aspects of the article.(February 2021)
A potato cannon, also known as a potato gun or potato launcher, is a pipe-based cannon that uses air pressure (pneumatic), or combustion of a flammable gas (aerosol, propane, etc.),[1][2][3][4] to fire projectiles, usually potatoes.[5] A simple design consists of a pipe sealed on one end, with a reducer on the other end to lower the diameter of the pipe, which has the corresponding lower-diameter pipe attached to it, called the barrel. Generally, the operator loads the projectile into the barrel, then utilizes a fuel or air pressure (or sometimes both) to propel the projectile out of the cannon.
Combustion powered potato cannons typically have the least complex designs; the four basic elements of which are:
A fuel-air mixture
A combustion chamber
An ignition source
A barrel
In order to fire, the operator loads a projectile into the barrel, adds fuel to the combustion chamber (for example aerosols or propane), and triggers the ignition source (often using a piezoelectric barbecue igniter). The fuel-air mixture then ignites, creating hot expanding gases which force the projectile out of the barrel. The range of the cannon depends on many variables, including the type of fuel used, the efficiency of the fuel/air ratio, the combustion chamber/barrel ratio, and the flight characteristics of the projectile. Common distances vary from 100–200 meters (330–660 feet), and there is a reported case of a cannon exceeding 500 meters (1,600 feet) of range.[7]
Pneumatic
A pneumatic potato cannonA large pneumatic design: The projectile is loaded in the muzzle (not pictured), which is then attached to the cannon (at 2). The air reservoir (3) is filled to 120 psi (0.83 MPa) using the Schrader valve (4). Upon opening the solenoid valve (1), the air from the reservoir is transferred to the projectile, which is fired out of the muzzle.
The range of pneumatic cannons is more variable than the range of combustion potato cannons due to the increased variation possible in the components. Typical ranges are slightly higher because of the greater power, but the maximum range of some high power pneumatic cannons has been said to be over 1,000 metres (3,300 ft).[8]
Hybrid
In order to fire, the operator first readies the pressure-triggered valve then injects several times the normal amount of fuel and appropriately more air. When the ignition source is triggered, the pressure from the combustion causes the main valve to open and propels the projectile out of the barrel with the released combustion gases. The hybrid is capable of higher velocities than a combustion or pneumatic potato cannon because the pressure generated is higher than that in a combustion gun (for most fuels), and the shock wave moves faster than it can in a pneumatic (for most gases), due to the higher temperature. Projectiles fired by a hybrid have broken the sound barrier.[9]
Dry ice
PVC dry ice cannon in use, 1.5kg (3 pounds) of concrete is poured at the bottom to reinforce it, and plastic sleeves are used to stiffen the lower (highest pressure) part.
The oldest examples simply involve dropping pieces of dry ice into a tube closed at one end and sealing the other end by jamming the projectile in. When the pressure of the carbon dioxide from the subliming dry ice builds high enough, the projectile will be blown out of the tube.[10]
PVC-U (Polyvinyl chloride, unplasticized): Highly popular due to its availability and relatively low cost. PVC pipes are available in a wide variety of sizes and pressure ratings. In industry, however, they are illegal for compressed air applications—if they are damaged under pressure the plastic can fail explosively.[11]
ABS (Acrylonitrile butadiene styrene): Another popular plastic piping material, more expensive and less common than PVC but available in the same sizes and pressure ratings. Unlike PVC it is used in compressed air systems as it splits rather than shatters on failure.[12]
Metals
Brass: Often brass fittings are used on potato cannons for small parts of the construction like fuel systems, because it is one of the most common materials for small pipe fittings. Occasionally large parts of potato cannons are machined entirely out of brass.[13]
Valve types
Pneumatic
The Quick Dump Valve is a recent addition to the choices of valves for spudding. A QDV is a spool valve that is balanced under pressure with one end of the spool oriented toward the barrel. The spool is manually unbalanced allowing pressure between the end of the spool and the projectile in the barrel. The air pressure then forces the spool back and the projectile forward. Since the valve is triggered with no pilot pressure, the valve snaps open with no pilot pressure to hinder it. Currently it is not commercially for sale and must be hand built by the hobbyist like most piston valves.[14]
Alternate designs have also been used which use a sharp projectile to puncture the burst disk, like a mortar[15] or using a manual puncturing device to trigger failure of the disk.[16]
Burst disk cannons have also been made which are fired electrically, using a nichrome wire to trigger failure by heating.[17]
Connections
Welding, soldering and gluing
Solvent welding: used for similar plastic connections using solvent fittings, the solvent temporarily dissolves the polymer chains of the plastic and the parts to be joined are brought together. On rehardening, the polymer chains from each part are entangled and so form a solid weld.[18]
The sound barrier
It is rare for a potato cannon to be powerful enough to break the sound barrier, although there are some cases of this happening using specialized designs. The potato cannons used are typically hybrids; but some pneumatic cannons have achieved the feat, either by using a special low-density gas, such as helium,[19] or high pressures combined with a fast valve.[20] There is also one reported case of a combustion design achieving super-sonic velocities.[7]
The highest projectile speed recorded from a potato cannon is 933.3 m/s (3,060 ft/s) (approximately 2.7 times the speed of sound) with a 16.6-gram (256 gr) 20 mm plastic slug from a hybrid using a 20 MPa (2,900 psi) pre-ignition mixture of air and propane.[21]
Supersonic velocities have been obtained using the related vacuum bazooka with a de Laval nozzle. This also relies on significantly lowering the density of the gas.[22]
Although potato cannons are created and used for the purpose of recreation there are other devices which work on identical principles in many other fields with more serious uses.
Entertainment
Promotional sports cannons: Portable pneumatic cannons which run on bottled CO2 are common at large sports games in the U.S. where they are used to project items such as T-shirts or wrapped food into the audience. Such cannons can be dangerous: the Phillie Phanatic injured a fan with a hot dog cannon in June 2018.[23]
Shock tubes: used to test hypersonic and supersonic combustion ramjets.[24]
Safety
Potato cannons by nature are hazardous and can present safety issues if poorly constructed or used. Projectiles or failing guns can be dangerous and result in life-threatening injuries, including cranial fractures, enucleation, and blindness if a person is hit.[25]
^ abBigBang (October 2006). "Crusader". SpudFiles. Archived from the original on 20 February 2009. Retrieved 2009-06-01.
^schmanman; et al. (March–April 2007). "(NEW) S.W.A.T v.3". SpudFiles. Archived from the original on 2 February 2013. Retrieved 16 August 2011. Cannon with a calculated range exceeding 1 mile.
^Killjoy (25 April 2007). "FEAR". SpudFiles. Archived from the original on 27 February 2015. Retrieved 2009-06-01.
^"New stuff". The Spudgun Technology Center. 14 January 2010 [6 July 2002]. Retrieved 16 August 2011. "Theory/physics behind the spudgun". The Spudgun Technology Center. 29 August 2008 [25 June 2002]. Retrieved 16 August 2011. Used helium to attain supersonic velocities.
^jackssmirkingrevenge (8 September 2007). "high velocity burst disc 6mm pneumatic". SpudFiles. Retrieved 16 August 2011. Attained approximately Mach 1 (340 m/s; 1120 ft/s) with 400 psi (2.8 MPa) and a fast valve.
