Geiger counter

Geiger–Müller counter
A "two-piece" bench-type Geiger–Müller counter using a cylindrical end-window detector connected to an electronics module with analogue readout
Other namesGeiger Counter
InventorHans Geiger,
Walther Müller
Related itemsGeiger–Müller tube
The sound of a geiger counter

A Geiger counter (/ˈɡɡər/, GY-gər;[1] also known as a Geiger–Müller counter or G-M counter) is an electronic instrument used for detecting and measuring ionizing radiation. It is widely used in applications such as radiation dosimetry, radiological protection, experimental physics and the nuclear industry.

"Geiger counter" is often used generically to refer to any form of dosimeter (or, radiation-measuring device), but scientifically, a Geiger counter is only one specific type of dosimeter.

It detects ionizing radiation such as alpha particles, beta particles, and gamma rays using the ionization effect produced in a Geiger–Müller tube, which gives its name to the instrument.[2] In wide and prominent use as a hand-held radiation survey instrument, it is perhaps one of the world's best-known radiation detection instruments.

The original detection principle was realized in 1908 at the University of Manchester,[3] but it was not until the development of the Geiger–Müller tube in 1928 that the Geiger counter could be produced as a practical instrument. Since then, it has been very popular due to its robust sensing element and relatively low cost. However, there are limitations in measuring high radiation rates and the energy of incident radiation.[4]

The Geiger counter is one of the first examples of data sonification.[5]

Principle of operation

Diagram of a Geiger counter using an "end window" tube for low-penetration radiation. A loudspeaker is also used for indication.

A Geiger counter consists of a Geiger–Müller tube (the sensing element which detects the radiation) and the processing electronics, which display the result.

The Geiger–Müller tube is filled with an inert gas such as helium, neon, or argon at low pressure, to which a high voltage is applied. The tube briefly conducts electrical charge when high energy particles or gamma radiation make the gas conductive by ionization. The ionization is considerably amplified within the tube by the Townsend discharge effect to produce an easily measured detection pulse, which is fed to the processing and display electronics. This large pulse from the tube makes the Geiger counter relatively cheap to manufacture, as the subsequent electronics are greatly simplified.[4] The electronics also generate the high voltage, typically 400–900 volts, that has to be applied to the Geiger–Müller tube to enable its operation. This voltage must be carefully selected, as too high a voltage will allow for continuous discharge, damaging the instrument and invalidating the results. Conversely, too low a voltage will result in an electric field that is too weak to generate a current pulse.[6] The correct voltage is usually specified by the manufacturer. To help quickly terminate each discharge in the tube a small amount of halogen gas or organic material known as a quenching mixture is added to the fill gas.

Readout

There are two types of detected radiation readout: counts and radiation dose.

  • The counts display is the simplest, and shows the number of ionizing events detected, displayed either as a count rate, such as "counts per minute" or "counts per second", or as a total number of counts over a set time period (an integrated total). The counts readout is normally used when alpha or beta particles are being detected.
  • More complex to achieve is a display of radiation dose rate, displayed in units such as the sievert, which is normally used for measuring gamma or X-ray dose rates. A Geiger–Müller tube can detect the presence of radiation, but not its energy, which influences the radiation's ionizing effect. Consequently, instruments measuring dose rate require the use of an energy compensated Geiger–Müller tube, so that the dose displayed relates to the counts detected.[4] The electronics will apply known factors to make this conversion, which is specific to each instrument and is determined by design and calibration.

The readout can be analog or digital, and modern instruments offer serial communications with a host computer or network.

There is usually an option to produce audible clicks representing the number of ionization events detected. This is the distinctive sound associated with handheld or portable Geiger counters. The purpose of this is to allow the user to concentrate on manipulation of the instrument while retaining auditory feedback on the radiation rate.

Limitations

There are two main limitations of the Geiger counter:

  1. Because the output pulse from a Geiger–Müller tube is always of the same magnitude (regardless of the energy of the incident radiation), the tube cannot differentiate between radiation types or measure radiation energy, which prevents it from correctly measuring dose rate.[4]
  2. The tube is less accurate at high radiation rates, because each ionization event is followed by a "dead time", an insensitive period during which any further incident radiation does not result in a count. Typically, the dead time will reduce indicated count rates above about 104 to 105 counts per second, depending on the characteristic of the tube being used. [4] While some counters have circuitry which can compensate for this, for measuring very high dose rates, ion chamber instruments are preferred for high radiation rates.

Types and applications

Geiger counter with pancake type probe
Laboratory use of a Geiger counter with end-window probe to measure beta radiation

The intended detection application of a Geiger counter dictates the tube design used. Consequently, there are a great many designs, but they can be generally categorized as "end-window", windowless "thin-walled", "thick-walled", and sometimes hybrids of these types.

Particle detection

The first historical uses of the Geiger principle were to detect α- and β-particles, and the instrument is still used for this purpose today. For α-particles and low energy β-particles, the "end-window" type of a Geiger–Müller tube has to be used, as these particles have a limited range and are easily stopped by a solid material. Therefore, the tube requires a window which is thin enough to allow as many as possible of these particles through to the fill gas. The window is usually made of mica with a density of about 1.5–2.0 mg/cm2.[2]

α-particles have the shortest range, and to detect these the window should ideally be within 10 mm of the radiation source due to α-particle attenuation.[2] However, the Geiger–Müller tube produces a pulse output which is the same magnitude for all detected radiation, so a Geiger counter with an end window tube cannot distinguish between α- and β-particles.[4] A skilled operator can use varying distance from a radiation source to differentiate between α- and high energy β-particles.

The "pancake" Geiger–Müller tube is a variant of the end-window probe, but designed with a larger detection area to make checking quicker. However, the pressure of the atmosphere against the low pressure of the fill gas limits the window size due to the limited strength of the window membrane.

Some β-particles can also be detected by a thin-walled "windowless" Geiger–Müller tube, which has no end-window, but allows high energy β-particles to pass through the tube walls. Although the tube walls have a greater stopping power than a thin end-window, they still allow these more energetic particles to reach the fill gas.[2]

End-window Geiger counters are still used as a general purpose, portable, radioactive contamination measurement and detection instrument, owing to their relatively low cost, robustness and relatively high detection efficiency; particularly with high energy β-particles.[4][7] However, for discrimination between α- and β-particles or provision of particle energy information, scintillation counters or proportional counters should be used.[8] Those instrument types are manufactured with much larger detector areas, which means that checking for surface contamination is quicker than with a Geiger counter.

Gamma and X-ray detection

A Radhound Geiger counter measuring radiation emitted by a tree in Chernobyl

Geiger counters are widely used to detect gamma radiation and X-rays, collectively known as photons, and for this the windowless tube is used. However, detection efficiency is low compared to alpha and beta particles. The article on the Geiger–Müller tube carries a more detailed account of the techniques used to detect photon radiation. For high energy photons, the tube relies on the interaction of the radiation with the tube wall, usually a material with a high atomic number such as stainless steel of 1–2 mm thickness, to produce free electrons within the tube wall, due to the photoelectric effect. If these migrate out of the tube wall, they enter and ionize the fill gas.[4]

This effect increases the detection efficiency because the low-pressure gas in the tube has poorer interaction with higher energy photons than a steel tube. However, as photon energies decrease to low levels, there is greater gas interaction, and the contribution of direct gas interaction increases. At very low energies (less than 25 keV), direct gas ionisation dominates, and a steel tube attenuates the incident photons. Consequently, at these energies, a typical tube design is a long tube with a thin wall which has a larger gas volume, to give an increased chance of direct interaction of a particle with the fill gas.[2]

Above these low energy levels, there is a considerable variance in response to different photon energies of the same intensity, and a steel-walled tube employs what is known as "energy compensation" in the form of filter rings around the naked tube, which attempts to compensate for these variations over a large energy range.[2] A steel-walled Geiger–Müller tube is about 1% efficient over a wide range of energies.[2]

Neutron detection

Geiger tube filled with BF3 for detection of thermal neutrons

A variation of the Geiger tube known as a Bonner sphere can be used to exclusively measure radiation dosage from neutrons rather than from gammas by the process of neutron capture. The tube, which can contain the fill gas boron trifluoride or helium-3, is surrounded by a plastic moderator that reduces neutron energies prior to capture. When a capture occurs in the fill gas, the energy released is registered in the detector.

A modern one-piece Geiger–Müller counter, including Geiger–Müller tube type 70 019 (at the top)

Gamma measurement—personnel protection and process control

While "Geiger counter" is practically synonymous with the hand-held variety, the Geiger principle is in wide use in installed "area gamma" alarms for personnel protection, as well as in process measurement and interlock applications. The processing electronics of such installations have a higher degree of sophistication and reliability than those of hand-held meters.

Physical design

Pancake G-M tube used for alpha and beta detection; the delicate mica window is usually protected by a mesh when fitted in an instrument.

For hand-held units there are two fundamental physical configurations: the "integral" unit with both detector and electronics in the same unit, and the "two-piece" design which has a separate detector probe and an electronics module connected by a short cable.

In the 1930s a mica window was added to the cylindrical design allowing low-penetration radiation to pass through with ease.[9]

The integral unit allows single-handed operation, so the operator can use the other hand for personal security in challenging monitoring positions, but the two piece design allows easier manipulation of the detector, and is commonly used for alpha and beta surface contamination monitoring where careful manipulation of the probe is required or the weight of the electronics module would make operation unwieldy. A number of different sized detectors are available to suit particular situations, such as placing the probe in small apertures or confined spaces.

Gamma and X-Ray detectors generally use an "integral" design so the Geiger–Müller tube is conveniently within the electronics enclosure. This can easily be achieved because the casing usually has little attenuation, and is employed in ambient gamma measurements where distance from the source of radiation is not a significant factor. However, to facilitate more localised measurements such as "surface dose", the position of the tube in the enclosure is sometimes indicated by targets on the enclosure so an accurate measurement can be made with the tube at the correct orientation and a known distance from the surface.

There is a particular type of gamma instrument known as a "hot spot" detector which has the detector tube on the end of a long pole or flexible conduit. These are used to measure high radiation gamma locations whilst protecting the operator by means of distance shielding.

Particle detection of alpha and beta can be used in both integral and two-piece designs. A pancake probe (for alpha/beta) is generally used to increase the area of detection in two-piece instruments whilst being relatively light weight. In integral instruments using an end window tube there is a window in the body of the casing to prevent shielding of particles. There are also hybrid instruments which have a separate probe for particle detection and a gamma detection tube within the electronics module. The detectors are switchable by the operator, depending the radiation type that is being measured.

Guidance on application use

In the United Kingdom the National Radiological Protection Board issued a user guidance note on selecting the best portable instrument type for the radiation measurement application concerned.[8] This covers all radiation protection instrument technologies and includes a guide to the use of G-M detectors.

History

Rutherford & Geiger particle counter (1908). Alpha particles from a source in the firing tube were admitted through aperture "D" to the detecting vessel, which was a brass tube with a central co-axial wire "B" at a relative potential of 1320 volts dc. The aperture had a mica window so the detecting vessel could run at a pressure of 2-5 mm of mercury. These conditions enabled creation of a Townsend avalanche for every alpha particle entering the vessel. At very low count rates these registered as "kicks" on an electrometer needle.
Early Geiger–Müller tube made in 1932 by Hans Geiger for laboratory use

In 1908 Hans Geiger, under the supervision of Ernest Rutherford at the Victoria University of Manchester (now the University of Manchester), developed an experimental technique for detecting alpha particles that would later be used to develop the Geiger–Müller tube in 1928.[10] This early counter was only capable of detecting alpha particles and was part of a larger experimental apparatus. The fundamental ionization mechanism used was discovered by John Sealy Townsend between 1897 and 1901,[11] and is known as the Townsend discharge, which is the ionization of molecules by ion impact.

It was not until 1928 that Geiger and Walther Müller (a PhD student of Geiger) developed the sealed Geiger–Müller tube which used basic ionization principles previously used experimentally. Small and rugged, not only could it detect alpha and beta radiation as prior models had done, but also gamma radiation.[9][12] Now a practical radiation instrument could be produced relatively cheaply, and so the Geiger counter was born. As the tube output required little electronic processing, a distinct advantage in the thermionic valve era due to minimal valve count and low power consumption, the instrument achieved great popularity as a portable radiation detector.

Modern versions of the Geiger counter use halogen quench gases, a technique invented in 1947 by Sidney H. Liebson.[13] Halogen compounds have superseded the organic quench gases because of their much longer life and lower operating voltages; typically 400-900 volts.[14]

See also

References

  1. ^ "Geiger counter | Pronunciation in English".
  2. ^ a b c d e f g ’’Geiger Muller Tubes; issue 1’’ published by Centronics Ltd, UK.
  3. ^ E. Rutherford and H. Geiger (1908) "An electrical method of counting the number of α particles from radioactive substances," Proceedings of the Royal Society (London), Series A, vol. 81, no. 546, pages 141–161.
  4. ^ a b c d e f g h Glenn F Knoll. Radiation Detection and Measurement, third edition 2000. John Wiley and Sons, ISBN 0-471-07338-5
  5. ^ "What is Sonification - Accessible Oceans". What is data sonificaiton. Woods Hole Oceanographic Institute. Retrieved 2024-05-30.
  6. ^ Siegel, Peter; Eskandari, Sephir. "Introduction to Geiger Counters" (PDF). Archived (PDF) from the original on 2017-02-21.
  7. ^ "G-M detector function and measuring methods". Retrieved 2017-03-07.
  8. ^ a b [1] Archived 2018-07-30 at the Wayback Machine Selection, use and maintenance of portable monitoring instruments. UK HSE
  9. ^ a b Korff, SNTM (2012) 20: 271. doi:10.1007 / s00048-012-0080-y
  10. ^ E. Rutherford and H. Geiger (1908) "An electrical method of counting the number of α particles from radioactive substances," Proceedings of the Royal Society (London), Series A, vol. 81, no. 546, pages 141–161.
  11. ^ John S. Townsend (1901) "The conductivity produced in gases by the motion of negatively charged ions," Philosophical Magazine, series 6, 1 (2) : 198-227.
  12. ^ See:
    • H. Geiger and W. Müller (1928), "Elektronenzählrohr zur Messung schwächster Aktivitäten" (Electron counting tube for the measurement of the weakest radioactivities), Die Naturwissenschaften (The Sciences), vol. 16, no. 31, pages 617–618.
    • Geiger, H. and Müller, W. (1928) "Das Elektronenzählrohr" (The electron counting tube), Physikalische Zeitschrift, 29: 839-841.
    • Geiger, H. and Müller, W. (1929) "Technische Bemerkungen zum Elektronenzählrohr" (Technical notes on the electron counting tube), Physikalische Zeitschrift, 30: 489-493.
    • Geiger, H. and Müller, W. (1929) "Demonstration des Elektronenzählrohrs" (Demonstration of the electron counting tube), Physikalische Zeitschrift, 30: 523 ff.
  13. ^ Liebson, S. H. (1947). "The Discharge Mechanism of Self-Quenching Geiger–Mueller Counters" (PDF). Physical Review. 72 (7): 602–608. Bibcode:1947PhRv...72..602L. doi:10.1103/PhysRev.72.602. hdl:1903/17793. Archived (PDF) from the original on 2017-09-21.
  14. ^ "History of Portable Radiation Detection Instrumentation from the period 1920–60". Archived from the original on 2009-01-13. Retrieved 2008-07-15.

Media related to Geiger counters at Wikimedia Commons

Read other articles:

Middle MenPoster resmiSutradara George Gallo Produser Christopher Mallick William Sherak Jason Shuman Michael Weiss Ditulis oleh George Gallo Andy Weiss PemeranLuke Wilson Giovanni Ribisi Gabriel Macht James CaanPenata musikBrian TylerSinematograferLukas EttlinPenyuntingMalcolm CampbellPerusahaanproduksiOxymoron Entertainment & Paramount PicturesDistributorParamount Vantage[1]Tanggal rilis 17 Mei 2009 (2009-05-17) (Cannes) 06 Agustus 2010 (2010-08-06) (Unit...

 

هذه المقالة يتيمة إذ تصل إليها مقالات أخرى قليلة جدًا. فضلًا، ساعد بإضافة وصلة إليها في مقالات متعلقة بها. (أبريل 2019) إلين شرايبر   معلومات شخصية تاريخ الميلاد 4 يونيو 1939[1]  تاريخ الوفاة 11 يونيو 2017 (78 سنة) [1]  الجنسية أستراليا  مشكلة صحية شلل الأطفال  الحياة

 

Pembajakan perangkat lunak adalah penyalinan atau distribusi perangkat lunak secara ilegal atau tidak sah. Biasanya sebuah program atau aplikasi hanya memberikan izin untuk satu pengguna dan satu komputer saja. Dengan membeli perangkat lunak, seseorang menjadi pengguna berlisensi atau berizin dan bukan pemilik. Jadi, jika seseorang menyalin dan memperbanyak perangkat lunak tersebut, maka itu disebut sebagai pembajakan perangkat lunak. Lisensi adalah sebuah izin yang memberitahu berapa kali pe...

La sinagoga de Acqui Terme, actualmente desmantelada, se encontraba en via Portici Saracco 1 en Acqui Terme, Italia. Tras la emancipación judía de 1848, la comunidad judía de Acqui Terme decidió ampliar el antiguo oratorio con una gran sinagoga. Las obras fueron financiadas por Jona Ottolenghi, miembro de una de las familias judías más importantes de la zona. Inaugurada la tarde del viernes 14 de diciembre de 1888, la monumental sinagoga construida por el Ingeniero Leale al estilo clás...

 

James Pigott PritchettBorn14 October 1789Died23 May 1868(1868-05-23) (aged 78)York, EnglandNationalityBritishOccupationArchitect This article is about the York architect (1789–1868). For his son, the Darlington architect (1830–1911), see James Pigott Pritchett Jr. James Pigott Pritchett (14 October 1789 – 23 May 1868) was an English architect. He lived in London and York and his practice stretched from Lincolnshire to the Scottish borders. Personal life Pritchett was born on 14 Oct...

 

1982 song written by Barry Mann and Cynthia Weil Never Gonna Let You GoSong by Dionne Warwickfrom the album Friends in Love ReleasedApril 14, 1982GenreAdult contemporary, R&BLength4:50LabelAristaSongwriter(s)Cynthia Weil, Barry MannProducer(s)Jay Graydon Never Gonna Let You GoSong by Stevie Woodsfrom the album The Woman in My Life Released1982GenreSoul, R&BLength4:54LabelCotillionSongwriter(s)Cynthia Weil, Barry Mann Never Gonna Let You GoSingle by Sérgio Mendesfrom the album Sérgio...

American art dealer Alexina Duchamp in 1993 Alexina Teeny Duchamp (née Sattler; January 6, 1906 – December 20, 1995) was the wife of Pierre Matisse, daughter-in-law of artist Henri Matisse, and second wife of artist and chess player Marcel Duchamp. Background She was born Alexina Sattler in Cincinnati, Ohio in 1906. The youngest daughter of prominent surgeon Robert Sattler, Alexina was nicknamed Teeny by her mother Agnes Mitchell because of her low birth weight. Paris and marriage to P...

 

This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these template messages) This article may rely excessively on sources too closely associated with the subject, potentially preventing the article from being verifiable and neutral. Please help improve it by replacing them with more appropriate citations to reliable, independent, third-party sources. (August 2018) (Learn how and when to remove this template message) ...

 

Public high school in the United StatesCerritos High SchoolThe Don CrestLocation12500 E. 183rd Street Cerritos, California 90703United StatesCoordinates33°51′53″N 118°03′50″W / 33.864726°N 118.063927°W / 33.864726; -118.063927InformationTypePublic high schoolEstablishedSeptember 1971School districtABC Unified School DistrictSuperintendentMary SieuPrincipalPatrick WalkerFaculty88.75 FTEs[1]Grades9–12Enrollment2,177 (as of 2018-19)[1]Student...

The Other Change of HobbitTypeBookstoreIndustrybooksellingGenreScience fictionFantasyFoundedMay 1977FounderDave NeeDebbie NotkinTom WhitmoreHeadquartersBerkeley, CaliforniaArea servedSan Francisco Bay AreaInternet The Other Change of Hobbit (sometimes abbreviated TOCOH) is a science fiction and fantasy bookstore, formerly located in Berkeley, California and then El Cerrito; it no longer has a physical location. It was founded in 1977, the same weekend that Star Wars opened.[1] It has ...

 

This article does not cite any sources. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed.Find sources: Wie wordt euromiljonair? – news · newspapers · books · scholar · JSTOR (July 2011) (Learn how and when to remove this template message) Belgian TV series or program Wie wordt euromiljonair?Nowadays logo of Wie wordt euromiljonair?Also known asWie wordt multimiljonair?Create...

 

Việt Nam Quốc TựReligionAffiliationBuddhismLocationLocation3 Thang 2, District 10, Ho Chi Minh CityCountry VietnamShown within VietnamGeographic coordinates10°46′16″N 106°40′24″E / 10.7711539°N 106.6732228°E / 10.7711539; 106.6732228ArchitectureCompleted1963 The Việt Nam Quốc Tự (lit. 'National pagoda of Vietnam') is located on February 3rd Blvd., District 10 of Ho Chi Minh City, Vietnam. The pagoda, seven stories tall, is full of...

قرية المعرس  - قرية -  تقسيم إداري البلد  اليمن المحافظة محافظة المحويت المديرية مديرية المحويت العزلة عزلة الغربي الاعلى السكان التعداد السكاني 2004 السكان 318   • الذكور 155   • الإناث 163   • عدد الأسر 37   • عدد المساكن 26 معلومات أخرى التوقيت توقيت اليمن (+...

 

Logo of the Young Generation Network The Young Generation Network, or YGN, is a branch of the Nuclear Institute founded in 1996. It is a British version of the European Young Generation Network created earlier in Sweden by Jan Runermark, a president of ABB Atom who had been concerned with preserving the know-how of retiring nuclear-energy pioneers and who perceived a need for greater efforts to retain young professionals. The YGN, which is open to NI members under the age of 37, organizes lec...

 

Ethnic group This article is about the indigenous tribe. For other uses, see Puyallup. Puyallup peopleTotal population6,700 (3,000 on the reservation)Regions with significant populationsUnited States (Washington)LanguagesEnglish, LushootseedRelated ethnic groupsother Salishan peoples The Puyallup, spuyaləpabš[1] or S’Puyalupubsh (pronounced: Spoy-all-up-obsh)[needs IPA] ('generous and welcoming behavior to all people, who enter our lands') are a federally recognized Coast ...

American medical comedy-drama television series ScrubsGenre Sitcom Comedy drama Medical drama Created byBill LawrenceStarring Zach Braff Sarah Chalke Donald Faison Neil Flynn Ken Jenkins John C. McGinley Judy Reyes Eliza Coupe Kerry Bishé Michael Mosley Dave Franco Narrated by Zach Braff Kerry Bishé (season 9) Theme music composer Chad Fischer Chris Link Tim Bright Opening theme Superman by Lazlo Bane (seasons 1–8) Superman by WAZ (season 9) ComposerJan StevensCountry of originUnited Stat...

 

LTO

LTO Официальный сайт lto.org (англ.)  Медиафайлы на Викискладе Картридж Ultrium LTO-2 LTO (англ. Linear Tape-Open) — стандарт записи на магнитную ленту, которому удовлетворяет большинство современных ленточных накопителей. Практически используемым форматом записи данных в этом с...

 

Museum in Riga, Latvia This article does not cite any sources. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed.Find sources: Museum of the History of Riga and Navigation – news · newspapers · books · scholar · JSTOR (February 2019) (Learn how and when to remove this template message) Museum of the History of Riga and NavigationRīgas vēstures un kuģniecības muzejsExterior of ...

The former home of the LRDC was a Harrison & Abramovitz designed building. The Learning Research and Development Center (LRDC) at the University of Pittsburgh is an interdisciplinary center focused on describing, understanding, improving, and researching various aspects of human cognition and learning in order to improve and reform instruction and training in schools, the workplace, and informal environments. Overview Co-founded in 1963 by Robert Glaser and J. Steele Gow,[1] it wa...

 

Structural analog of methamphetamine MethiopropamineClinical dataOther namesMPA; Methiopropamine; Methedrene; SyndraxATC codeN06AA Legal statusLegal status BR: Class F2 (Prohibited psychotropics)[1] DE: Anlage I (Authorized scientific use only) UK: Class B US: Schedule I Illegal in China, Finland, Florida Identifiers IUPAC name 1-(thiophen-2-yl)-2-methylaminopropane CAS Number801156-47-8 N 7464-94-0 (hydrochloride)PubChem CID436156ChemSpider385727 YU...

 

Strategi Solo vs Squad di Free Fire: Cara Menang Mudah!